IPA 99,8 % ou 70/30 : quel isopropanol pour quel usage ?
Alcool isopropylique

99.8% or 70/30 IPA: which isopropanol for which application?

Key takeaways

  • IPA 99.8% is an option to consider for precision cleaning when water introduction must be kept to a minimum, particularly on powered-off electronic components and compatible optical surfaces.
  • 70/30 IPA is suitable for routine cleaning of compatible surfaces and is intended for preparation before bonding or painting.
  • 70/30 is not a registered disinfectant: for biocidal or medical use, the product, its spectrum of activity, and the protocol must be authorized for the intended use.

How to choose: precision cleaning with minimal water introduction → IPA 99.8%; surface cleaning and preparation before bonding → IPA 70/30; regulated disinfection → authorized biocide.

The choice between 99% and 70% isopropyl alcohol depends on the contaminant, the substrate, the required drying time and the regulatory status of the operation.

Why distinguish between precision cleaning, surface cleaning and disinfection?

Isopropyl Alcohol / Isopropanol IPA 99.8% is a technical-grade product with a minimum mass concentration of 99.8%. It is used as a solvent for waxes, oils, and resins and to clean integrated circuits and semiconductors.

The 70/30 Isopropyl Alcohol Isopropanol IPA contains 70% IPA in an aqueous solution. It is intended for cleaning surfaces and preparing them before bonding or painting. This product should not be confused with a biocidal or medical product.

Professional need Option to consider Reason for choosing it Point to watch
Powered-off circuit or connector 99.8% IPA Limit water exposure Test varnishes, resins and plastics
Compatible optical components 99.8% IPA Fine cleaning Follow the manufacturer’s instructions
Before bonding or painting 70/30 or 99.8% Depends on the contaminant and specifications Confirm with the adhesive supplier
Surface to disinfect Authorized biocide Regulatory status takes precedence Check the spectrum of activity and contact time

Which IPA should you choose for each professional use?

1. Clean an electronic circuit or connector

For a de-energized component, 99.8% IPA is appropriate when the process aims to minimize residual water. Apply it with a clean, lint-free wipe or cloth, without soaking sensitive areas. Conformal coatings, markings, resins, seals, and polymers should be tested before widespread use.

2. Clean an optical component or glass surface

A bare glass surface may react differently from a bonded or coated lens. Anti-reflective coatings and some optical adhesives may be sensitive to solvents.

The optical component manufacturer’s recommendations take precedence, even when 99.8% IPA helps minimize the amount of water introduced.

3. Prepare a surface before bonding or painting

The 70/30 is intended for surface preparation before bonding and painting. The 99.8% grade may be considered if the specifications require a low water content. The choice must be validated against the actual contaminant, using the selected wipe or cloth and accounting for the planned time before applying the adhesive or coating.

4. Clean a pharmacy or laboratory workbench

For routine cleaning outside medical use, 70/30 may be considered on a compatible surface. If the procedure is intended to disinfect, alcohol concentration alone is not enough: an authorized biocide must be used according to its spectrum of activity, contact time and directions for use.

Advice from our laboratory

Do not judge cleaning performance based solely on the product’s concentration. Test the product and cleaning material together on a representative part, check for residue or damage, then establish a drying criterion before restoring power, bonding, painting, or packaging. 

Professional cleaning of a precision optical lens with a lint-free wipe

99.8% or 70/30 IPA: comparison 

Criterion 99.8% IPA 70/30 IPA
Recommended use Solvent and precision cleaning Surface cleaning and preparation before bonding
Water introduced Very limited Contains an aqueous phase
Drying Suitable for moisture-sensitive processes To be incorporated into the production cycle
Disinfection No biocidal claim for this grade Product not registered for biocidal or medical use

Cleaning procedure to be validated

1. Identify the contaminant and the surface

Distinguish between oils, flux, handling marks, dust, adhesive residue and water-soluble deposits. Also identify any polymers, varnishes, optical coatings and seals present.

2. Check compatibility

Consult the surface, adhesive or coating manufacturer’s instructions. Test a representative area and check for changes in color or gloss, cracking, softening and marks.

3. Make the workstation safe

Disconnect the power, move ignition sources away, and follow the ventilation, storage and PPE measures specified in the SDS and risk assessment.

4. Clean with a suitable wipe or cloth

Use a clean, lint-free wipe or cloth. Switch to a clean side as soon as it becomes soiled to avoid redistributing contaminants.

5. Dry and inspect

Wait until the surface is completely dry, as specified by the procedure, before restoring power, bonding, painting or packaging. Check cleanliness by visual inspection or using the qualified internal method.

Note: for any critical application (particularly in high-precision optics or on polymers sensitive to internal stresses), prior validation through testing on representative samples remains the golden rule before scaling up to production.

Mistakes to avoid with isopropyl alcohol

Mistake Why avoid it
Automatically choose the most concentrated product A higher concentration does not remove every contaminant more effectively, particularly water-soluble or mixed deposits.
Use IPA on energized equipment The product is flammable and must be completely dry before the equipment is put back into service.
Presenting 70/30 IPA as a disinfectant The product page excludes biocidal and medical uses for this product.
Use the same cloth across the entire surface A contaminated wipe or cloth can redistribute oils, flux or particles.
Bond immediately without a drying criterion Moisture or redistributed contaminants can affect adhesion and repeatability.
Generalize from a test on a single plastic Resistance varies with the polymer, internal stresses, additives and coatings.

How should used wipes and solvents be disposed of?

Cloths, wipes, and leftover product may be contaminated with oils, fluxes, inks, adhesives, or resins. They must be identified, stored in a compatible, closed container, then sent to the disposal stream designated by the site and its waste contractor.

Process: identify the waste → determine the contaminants → comply with the site's storage requirements → select the appropriate disposal route. Do not discharge into the sewer system without first characterizing the waste.

Which Arcane Direct products should you choose?

Need Product Packaging options
Precision cleaning Isopropyl Alcohol / Isopropanol IPA 99.8%  Listed formats: 6 x 1 L, 4 x 5 L, 20 L, 200 L drums, 1,000 L IBCs and wipes
Surface cleaning and preparation before bonding 70/30 Isopropyl Alcohol Isopropanol IPA 6 x 1 L, 4 x 5 L, 20 L, 200 L drum, 1,000 L IBC and 54 wipes

Explore our collection of professional solvents, plastic degreasing solutions, and pre-painting preparation products.

Need to validate your cleaning protocol?

The Arcane Direct team can help you choose the concentration, packaging and wipe or cloth. Tell us about the surface, contaminant, volume and next step in your process.

REQUEST A TECHNICAL CALLBACK OR A QUICK QUOTE

Product(s) featured in this article

Isopropyl Alcohol 70/30 Isopropanol IPA - CAS No. 67-63-0 - Carton 6x1L Isopropyl Alcohol 70/30 Isopropanol IPA - CAS No. 67-63-0 - Carton 6x1L
Carton 6x1L
Vendor:
Regular price 33,50€ excl. VAT
Sale price 33,50€ excl. VAT Regular price excl. VAT
Isopropyl Alcohol / Isopropanol IPA 99.8% - CAS No. 67-63-0 - Carton 6x1L / Technical Isopropyl Alcohol / Isopropanol IPA 99.8% - CAS No. 67-63-0 - Carton 6x1L / Technical
Carton 6x1L / Technical
Vendor:
Regular price 37,50€ excl. VAT
Sale price 37,50€ excl. VAT Regular price excl. VAT
Back to blog
Learn more

Which isopropyl alcohol should I choose, 99.8% or 70%?

Choose 99.8% IPA when the process requires minimal water content and precision cleaning. Use 70/30 for routine cleaning or preparation before bonding and painting compatible surfaces, after confirming adequate drying.

Which IPA should I use to clean an electronic circuit?

99.8% IPA is the option to consider when water content must be kept low. The circuit must be powered off, the materials must be compatible, and it must not be put back into service until completely dry.

Can Arcane Direct IPA 70/30 be used for disinfection?

No, it does not carry a biocidal or medical claim. This product is intended for surface cleaning only. For disinfection, use a product authorized for the intended application and follow its contact time instructions.

Is IPA suitable for lenses and anti-reflective coatings?

Only if the optical component manufacturer permits it. Anti-reflective coatings, optical adhesives, and polymers may be sensitive to solvents; a preliminary test does not replace the manufacturer’s instructions.

Which IPA should I choose before bonding?

The 70/30 is specifically intended for surface preparation before bonding or painting. The 99.8% may be considered when water exposure needs to be limited. In both cases, the adhesive supplier must confirm the procedure, drying time, and compatibility.